Use the Flipping Mount 5F21-1 to place optics in and out of the optical scheme. Flip the platform out and back again, and it sits on the driving screws in a repeated position. Precise alignment of various optical elements to desired angles is done by 2 driving screws. 3 seats form 3 kinematic points for definite position of the platform. These seats are of hardened steel – increasing the service life, as they are countering the hardened steel tips of driving screws and the flipping pivot balls. To flip, pull the platform by the horn (with the fixing screw in it). Platform pivots on two balls located on the opposite side. Flipped in or out it stays preloaded by springs. Flipping Mount is made of aluminium and can be anodized in a color to your request. Without special note from you we would supply mounts in black colour.

5F21-2-SH the ending SH mean that shown model has hex screws insted of screws with knobs as in main model 5F21-2.

Precise and handy adjustments, those angular in two
orthogonal planes, and linear
Stable vertical mounting
Adjustment range of 9° and 5 mm
Sensitivity of 3arcsec and 1µm
Made of black anodized aluminium


Kinematic Mirror/Beamsplitter Mounts 5MBM21-1 is ideally suitable for precise alignment of various optical elements to desired angular and linear orientation. The base of the stage has three holes Ø8.7mm for driving screws – Fine Screws 9S127 or 9SH127. The driving screw pushes the alignment plate with its hardened steel ball-tip. Mount 5MBM21-1 has a one inch mounting hole with Ø24 mm clear aperture. 5MBM21-1 is mounted using an M6 mounting screw at any of the two M6 holes on the sides of the base. Also it mounts directly on any STANDA Post Holder or Mounting Post on their M6 tips. Alternatively you put an M4 screw through the combined Ø7-to-M6 hole to fasten the mount to a unit with M4 hole. The Precision Kinematic Optical Mounts are produced of aluminium and can be anodized in a color according to your request. Without special note from you we would supply mounts in black colour. To specify how many screws you want in a mount, append the number to the code. Sufix "SH" specifies hex screw.

For Ø25.4 mm (1 inch) optics
Clear aperture 23 mm
Kinematic design
Dimensions most compact among 1 inch optics
mounts
Tilt/tip range ±2°
Sensitivity 3 arcsec
Both tilt and tip controlled from aside the optical
path
Ideal for dense optical schemes
Fine adjustment screws with 0.25mm pitch
Hardened seats under driving screws
Rotation range 360°
Scale gradation 2°


5APH69T-1 Kinematic Adjustable Polarizer Holder of Side Drive is similar to 5APH59T-1 Adjustable Polarizer Holder the only difference is that 5APH69T-1 has kinematic design and 5APH59T-1 has L-shaped flat spring. 5APH79T-1 Kinematic Double Optical Mount of Side Drive with Adjustable Polarizer Holder accepts two pieces of optics: on the platform (adjustable), and on the base (not adjustable). The fixing screw for optics on the base has a plastic tip. A retaining ring M27x1 to fix the optics is included. A tightening key 3K-25 for the retaining ring is available on request.

Read any of the 2 scales that space allows to
view (located on face and cylindrical sides)
Compact design with roller bearings
Lockable
Continuous 360° rotation
Direct mounting of optics 1" to 2" in diameter
Horizontal and Vertical mounting


Polarizer Holders 5PH50 are ideal for positioning rotation sensitive optics such as polarizers or waveplates. Holders are offered for optics 1" and 2" in diameter. Optics is placed inside central aperture, where it is securely held in place by a threaded retaining ring. The position is indicated on two 360° angular scales, with gradation of 2°. Where space doesn't allow to read one scale, you always will be able to view another. The base of a holder has threaded holes M6 and M4 for mounting on posts or bases. 5PH50 has a removable rod to rotate the platform by any of its 4 holes.

Polarizer Holders 5PH50-H are the same as 5PH50, except that their fixing screw is tightened with a hex-key (supplied), and it doesn't stand out from the surface. Like in 5PH50, the platform is rotated by any rod or the same hex key. The holders are made of black anodized aluminium.

Revolving scale resets the angular position
Conical scale easily read from a wide angle
Continuous 360° rotation
Lockable
Direct mounting of 1" (25.4mm) optics; 2" model
available
Accepts optics 19 mm thick
Mounting holes M6 and M4
Compact design with roller bearings


Polarizer Holder 5PH51-1 is an original mount with revolving conical angular scale on the face of the holder. This enables the user to set the current position on the scale to any chosen angle independently of the position of the holder. An optical element is secured inside central aperture of the platform of the holder by the threaded retaining ring. The zero on the revolving scale is aligned to the desired axis of transmission. For example rotate the platform to choose the required orientation of polarization. Lock the latform with its fixing screw. Revolve the scale to reset its zero origin. Lock the scale by etightening its own two fixing screws. Now the scale moves simultaneously with the platform of the holder, so you measure angles relative to any initial position. The holder accommodates rotation sensitive optics 1\" (25.4 mm) in diameter also 2\" model available.The scale is graduated into 2° increments. It is engraved on a conical surface. Angle of the cone is 60°. So the scale is read from a wide angle. The platform rotates the whole 360°. It has a knurled edge for fingers. Also it has 4 holes on its perimeter. Use the same 1.5 mm hex-key to rotate the platform by these holes, to lock the platform, and to lock the revolving conical scale. The base of a holder has both M6 and M4 holes to mount it on posts or bases. Yet the holder features a compact design. The holder is made of black anodized aluminium.

Base of 5PHH50 has beveled sides for fingers to rotate the platform by its knurled edge. You may transform a polarizer holder into a rotation stage. For this you'd need to order an insert platform 5PHH50-1A1 separately. To mount components on it the platform has a pattern of M4 holes and a central Ø7-to-M6 hole. If you need to fasten to the central hole a unit with M4 mounting hole, you can slip an M4 screw through this Ø7-to-M6 combined hole (see the drawing for 5PHH50-1).

Precise and handy two orthogonal angular
adjustments
Stabile vertical mounting
9° range
Various modifications with sensitivity from
10arcsec to 3arcsec
Made of black anodized aluminium
Weight 0.08 kg


The Beamsplitters/Optics Mount 5BM121 is designed for adjustments of beamsplitters measuring Ø25 mm. Fixing screw with a plastic tip clutches a beamsplitter against stainless steel rests. The aperture has a rest-flange around its edge designed to stop optics inside.

Precision Kinematic Optical Mounts are ideally suitable for precise aligning of various optical elements to desired angular orientation. The tilting element is always true-kinematic-registered. The drive screw pushes the alignment mechanism via hardened steel balls. These mounts provide angular range 9° in both orthogonal axes. The Precision Kinematic Optical Mounts are produced of aluminium and can be anodized in the color according to your request. Without special note from you will be provided with the black anodized Precision Kinematic Optical Mounts.

Precise and handy two orthogonal angular
adjustments
Stabile vertical mounting
9° range
Various modifications with sensitivity from
10arcsec to 3arcsec
Made of black anodized aluminium


The Large Aperture Optical Mount 5LAM124 on its platform has Ø31.8 mm aperture and six M4 mounting holes. It is designed for precise orthogonal adjustment of mirrors. The Large Aperture Optical Mount 5LAM124-2 on its platform has Ø50 mm aperture and three M4 mounting holes.

Precision Kinematic Optical Mounts are ideally suitable for precise aligning of various optical elements to desired angular orientation. The tilting element is always true-kinematic-registered. The drive screw pushes the alignment mechanism via hardened steel balls. These mounts provide angular range 9° in both orthogonal axes. The Precision Kinematic Optical Mounts are produced of aluminium and can be anodized in the color according to your request. Without special note from you will be provided with the black anodized Precision Kinematic Optical Mounts.

Precise and handy two orthogonal angular
adjustments
Stabile vertical mounting
9° range
Various modifications with sensitivity from
10arcsec to 3arcsec
Made of black anodized aluminium
Weight 0.09 kg


The Objective Mount 5OBM119 has W0.8-36 aperture and is used for precise adjustments of standard microscope objective lenses and ensures low-cost positioning of a focus point. Also it can be used in the fiber optics.

Precision Kinematic Optical Mounts are ideally suitable for precise aligning of various optical elements to desired angular orientation. The tilting element is always true-kinematic-registered. The drive screw pushes the alignment mechanism via hardened steel balls. These mounts provide angular range 9° in both orthogonal axes. The Precision Kinematic Optical Mounts are produced of aluminium and can be anodized in the color according to your request. Without special note from you will be provided with the black anodized Precision Kinematic Optical Mounts.

Precise and handy two orthogonal angular
adjustments
Stabile vertical mounting
9° range
Various modifications with sensitivity from
10arcsec to 3arcsec
Made of black anodized aluminium
Weight 0.1 kg


The Universal Mirror Mount/Platform 5UM122 is suited for precise adjustments of standard mirrors which can be directly bound to it. The Mount may also be used in horizontal position as a tilt table. Then it can be used to align opto-mechanics around two axes. For such mounting the Mount has an M4 hole on the back side.

Precision Kinematic Optical Mounts are ideally suitable for precise aligning of various optical elements to desired angular orientation. The tilting element is always true-kinematic-registered. The drive screw pushes the alignment mechanism via hardened steel balls. These mounts provide angular range 9° in both orthogonal axes. The Precision Kinematic Optical Mounts are produced of aluminium and can be anodized in the color according to your request. Without special note from you will be provided with the black anodized Precision Kinematic Optical Mounts.

Dimensions most compact among 1" optics
mounts
Both tilt and tip are controlled from aside the
optical path
Ideal for dense optical schemes
Fine adjustment screws with 0.25mm pitch
Hardened inserts under adjusters
Original stabilized L-shaped flat spring
Accepts optics 25.4 mm (1")in diameter
Tilt/tip travel range ±2°
Two pick-hollows allow keeping grip on optics
while reinserting
Horizontal and Vertical mounting
Mounting holes M4 on three sides


Adjustable Beamsplitter Mount of Side Drive 5BM59T-1 complements our range of SeriesT mounts with additional features, e.g. pick-hollows, or yet more stabilized spring. The style of the mount relates to such units as 5APH59T-1 and 5MBM21-1. The mount accepts optics 25.4 mm in diameter. Optics is stopped by a rest-flange inside the central aperture of the platform, and is secured by a steel hex fixing screw. The fixing screw has a hard plastic tip to prevent damage to the optics. To allow an unimpeded access for your fingers there are two pick-hollows. No more hassle and stains while picking the optics out... No more dropping the optics before you put it in securely. Pick-hollows form two contact points in the aperture. Clamped by the fixing screw, optics rests against these two points, so its position stays definite. Angular adjustment range of tilt/tip is ±2°. Side control of tilt and tip is done by two stainless steel fine adjustment screws with pitch of 0.25mm. The screws push rolling balls against hardened seats, ensuring smooth operation and sensitivity of 3 arcsec. Large knobs of the screws ease the strain on you fingers that this stabilized system might cause. Both screws protrude from the top. This control from a side allows easy access, and dense placement of surrounding instruments. The platform is preloaded against the base with L-shaped flat spring of our original design which renders the great stability and eliminates induced polarization. Three M4 tapped holes on the sides of the base and on its back allow a variety of mounting configurations, e.g. horizontal and vertical. The holder easily mounts on posts and bases. The holder is made of black anodized aluminium. L-shaped spring is made of high quality stainless spring steel.

For Ø25.4 mm (1 inch) optics
Clear aperture 23 mm
Kinematic design
Dimensions most compact among 1 inch optics
mounts
Tilt/tip range ±2°
Sensitivity 3 arcsec
Both tilt and tip controlled from aside the optical
path
Ideal for dense optical schemes
Fine adjustment screws with 0.25mm pitch
Hadened seats under driving screws
5BM79T-1 accepts two pieces of optics:
- on the platform (adjustable),
- on the base (not adjustable)

Tilt and in-plane rotation
Compact design for dense optical schemes
Stable design


Miniature Tilt/Rotation Mount 5OM101T allows you to tilt a component and to rotate it. To reduce the footprint and to ease access, both adjustment screws are placed on one side – the top – this saves space in schemes where units are placed densely. A flat spring preloads three main pieces of the mount which make it bend on two separate pivot axes. Mounts of other designs have a common pivot point for all adjustments. The design ensures that both adjustment movements are independent and do not cause mutual distortions. So the adjustment scheme is very close to an ideal kinematic model. Mounting surface with two M4 holes in the platform is on the same side with the adjustment screws. Base of the mount has an M4 hole for mounting to other positioners. The adjustment screws have a pitch of 0.25mm. They allow adjustment of tilt and in-plane rotation in the range of 6° (±3°). Each screw has a hex hole for a 3mm hex key.

Single side drive
Tilt/tip ±5° about two orthogonal axes
Fine adjustment screws with 0.25mm pitch
Hardened seats under driving screws
Sensitivity 10 arcsec
Large assortment of additional adapters
Material: black anodized aluminium


5OM10T is designed to hold optics in schemes of high density. Adapters are available for round and rectangular lenses, mirrors and beamsplitters or polarizing cubes (see below). The unit mounts on one M4 hole in its base. Special Base Mounts (see below) and standard ones are available in order to mount the unit in various orientations. A platform has four M3 holes on its face for mounting of optics, and three M4 holes on the sides for adapters. Adapters with connecting cones match the Ø6.2mm hole, where a cone is clutched by the fixing screw. A platform is preloaded against a base by coil springs. The mount is held together and stabilized by a flat spring.

Mirror Mount of Side Regulation 5OM122T enables to greatly increase the thickness of optical elements as it has a convenient access to the regulation handles. L-shaped flat spring of original design renders the great stability of the mount's platform. Angular range is ±2.5° about each of two orthogonal axes. Precision screws with pitch of 0.25 mm render sensitivity of 3 arcsec. M4 tapped holes on the sides of the base allow a variety of mounting configurations, e.g. horizontal and vertical. The mount is produced from black anodized aluminium. L-shaped spring is produced from high quality stainless spring steel. Mirror Mount of Side Regulation 5OM122T. Eccentric mounting holes Ø6.2 for connecting cone allow handy replacement and adjustment of Adapters to required place.
Mirror Mount of Side Regulation 5OM122TE. This variant has no clear aperture. This makes it an ideal tilt platform. The clear of holes flat surface allows to mount or paste mirrors on it.
Special Base Mounts 5OM122B allow 5OM122T to be mounted in different positions.5OM122T may be mounted as a tilt platform.

Miniature mounts for small optics
±10° tilt adjustments about two orthogonal axes
High degree of versatility
Is made of black anodized aluminium


The extremely smallmount has small driving screws with a hexagonal head or a hexagonal keyhole. A suffix to the unit code specifies driving screws of desired type or drive. (see the drawings for more info...) Miniature Precision Mirror Mounts ensure precise angular adjustments of small optic about two orthogonal axes with 10 arcsec sensitivity. For mounting the M4 and M6 taped holes are provided. These black anodized aluminium mounts are ideal for holding of 25 mm and smaller optic in tight spaces.

Miniature mounts for small optics
±10° tilt adjustments about two orthogonal axes
High degree of versatility
Is made of black anodized aluminium


Lock Screws Mirror Mounts 5LSM110 are provided with extended back for convenient mounting in horizontal or vertical position. Teflon fixture or driving screws ensures stability during explotation. Miniature Precision Mirror Mounts ensure precise angular adjustments of small optic about two orthogonal axes with 10 arcsec sensitivity. For mounting the M4 and M6 taped holes are provided. These black anodized aluminium mounts are ideal for holding of 25 mm and smaller optic in tight spaces.

Mirror/Optics Mount 5OM111 provides smooth and precise adjustment with sensitivity of 10 arcsec. It can be used as a tilt platform - with Spring Clamp 4SC-28T and Mounting Post 3SMP4-47. The mount has holes of M6x0.35 mm pitch on its base for adjustment screws. As standard, fine screws 9S67 are used. Alternatively, to order the mount with wrench driven screws, you append the code of that screw: 5OM111-9S127H (see variety of screws here...). Platform of the mount has a clear aperture of 6.2 mm in diameter. Weight: 0.045 kg.

True Gimbal design
Graduated adjustment knobs
±2.5° angular range
Hardened steel drive for stability
Lightweight aluminium body

Gimbal Mount has two plastic padding rings and a retaining ring M27x1 to fix the optics are included. A tightening key 3K-25 for the retaining ring is available on request.

An Adjustable Height Post 5HP18 is used both for coarse setting of Post mounted optics in the height range of 50 mm, and for finer adjustment over a height range of 7.5 mm (see below). The post has a moving chuck with a mounting opening for mounting posts. This precise opening is double bored along the inner wall to form two lines of contact for mounting posts 12 mm in diameter. Thus a precision mounting post slips into a definite state and doesn't play in the chuck. Use adapters 3AH to attach 5PH18 directly to various surfaces. Material: steel with black finish.

Coarse adjustment. Move the mounting post inside the chuck by hand and lock its position by a thumbscrews. Fine adjustment. One revoliution of the knurled ring moves the chuck with a post holder in it along its axis by 1.33 mm without rotation. Chuck's position is locked by another thumbscrew.

Travel range 3 mm
The movable carriage could accept Ø25,4 optics
up to 9mm thick
Alternatively, the movable carriage could be
used to mount additional lens tubes
Fine adjustment screws with 0,25 mm pitch


Two plastic padding rings and a retaining ring M27x1 to fix the optics are included. A tightening key 3K-25 for the retaining ring is available on request.

Weight 0.5 kg


Adjustable Height Platform 5VT173-25 of original design is a stable vertical translation stage of 25mm travel range. Maximum load capacity – 20kg. A polished lead screw has 0.5 mm pitch. It allows to define the height of a platform with 20 µm sensitivity. Arrays of mounting holes M6 and Ø6.5 with 25mm spacing are identical on the upper and lower plates. Adjustable Height Platform is ideal for use with 7T173-50 or 8MT173-50 Translation Stages when it is necessary to define one or two horizontal coordinates at a certain height. The platform is produced from black anodized aluminium, the lead screw block is produced from stainless steel and bronze.

Y-Z Positioner for Lens, Pinholes and Objectives 5ZYP are compact mounts designed to precisely position optical components in the plane orthogonal to the optical axis. Ideal for microscope objectives, mounted pinholes, fiber optics chucks, and diode lasers. The mounts provide 5 mm translation with sensitivity of 2 µm. 5ZYP-1 includes two adapters: W0.8 and 1". 5ZYP-2 includes one 2 inch adapter. Two Standa adjustment screws are used for positioning. They can be replaced with any screw or micrometer with M10x1 mounting thread.

The stage comes with 9S65M screw as standrad. You don't have to specify this screw in your order. If you order the stage with alternative screws, please specify this in order, by appending the screw code name to the stage code. See section "Fine Adjustment Screws" for screws and their codes. Two ways to fasten 5ZYP: by an M6 hole; on a connecting cone 3CC4, 3CC6 by a Ø7 hole. Material: black anodized aluminium.

Weight 0.3 kg


Self-made Pinholes Y-Z Mount 5ZYPS has two screws to adjust the pinhole about two axes in 5 mm range. 5ZYPS has a pinhole holder mounted - 14 mm in diameter with 3 mm clear aperture, made of steel. On request we supply pinholes. Or you may insert a Æ 7 mm disk of thin sheet of any material into this holder, and will be able to make a hole at any desired position using any available method (e.g. with a needle). 5ZYPS has three M6 holes and it can be mounted on Mounting Post 3MP6.